Test Information:
Total Questions: 240
Test Number: E20-690
Vendor Name: EMC
Cert Name: EMCPE
Test Name: VNX Solutions Specialist Exam for Platform Engineers
Official Site: http://www.certsgrade.com
For
More Details: http://www.certsgrade.com/pdf/E20-690/
Version 5.0
Question: 1
Which VNX
enclosures use a common motherboard architecture?
A. DME and SPE
B. DPE and SPE
C. DPE and
25-drive DAE
D. Control
Station and DME
Answer: A
Question: 2
What protocols
does the Data Mover support?
A. CIFS, NFS,
pNFS and MPFS
B. CIFS, pNFS,
and SCSI
C. MPFS, HTTP,
FTP, and NFS
D. NFS, FC, and
CIFS
Answer: A
Question: 3
What are the
minimum components required to configure a VNX5500 for Block storage system?
A. Control
Station, SP, DAE
B. Control
Station, SP, DME
C. SP, DME, DAE
D. SPS, SPE, DAE
Answer: D
Question: 4
Which kind of
back-end bus connectivity is supported on a VNX storage system?
A. 4 lane 6 Gb/s
SAS
B. 4 lane 6 Gb/s
FC
C. 2 lane 6 Gb/s
SAS
D. 2 lane 6 Gb/s
FC
Answer: A
Question: 5
How are SAS bus
hardware IDs configured for the VNX enclosures?
A. Automatically
assigned during system boot process
B. Assigned by
the address switch located on each enclosure
C. Assigned by
Unisphere Service Manager
D. Assigned by
the Backend Bus Reset Wizard in Unisphere
Answer: A
Question: 6
A customer asks your
help in determining which types of DPE and disk drives are supported in a VNX
storage system. How would you respond?
A. 2U DPE with
either fifteen 2.5” SAS or twenty-five 3.5" EFD disk drives
B. 3U DPE with
either fifteen 3.5” EFD, SAS or twenty-five 2.5" SAS disk drives
C. 4U DPE with
either fifteen 3.5” FC, EFD or twenty-five .2.5" SAS disk drives
D. 3U DPE with
either fifteen 2.5” EFD, FC or twenty-five 2.5” EFD disk drives
Answer: B
Question: 7
Refer to the
exhibit.
Where is DM 3
located?
A. Location 6
B. Location 5
C. Location 7
D. Location 10
Answer: A
Question: 8
What IP address
is assigned to the eth2 interface on a Control Station?
A. IP address for
the B management network
B. IP address for
the A management network
C. Public IP
address for the customer's network
D. IP address for
the peer Control Station
Answer: A
Question: 9
What IP address
is assigned to the eth3 interface on a Control Station?
A. IP address for
the A management network
B. IP address for
the B management network
C. Public IP
address for the customer's network
D. IP address for
the peer Control Station
Answer: C
Question: 10
Refer to the
exhibit.
Which component
is located in location 3?
A. CS 1
B. CS 0
C. DAE 0
D. DAE 1
Answer: A
Question: 11
Refer to the
exhibit.
Which DAE and
components does cable 1 connect?
A. SP A slot 0
port 1 to the SAS expander on DAE 0 LCC A
B. SP A slot 0
port 0 to the SAS expander on DAE 1 LCC A
C. SP B slot 0
port 0 to the SAS expander on DAE 1 LCC B
D. SP B slot 0
port 1 to the SAS expander on DAE 0 LCC B
Answer: A
Question: 12
Refer to the
exhibit.
Which DAE and
components does cable 2 connect?
A. SP A slot 0
port 0 to the SAS expander on DAE 1 LCC A
B. SP B slot 0
port 1 to the SAS expander on DAE 0 LCC B
C. SP B slot 0
port 0 to the SAS expander on DAE 1 LCC B
D. SP A slot 0
port 1 to the SAS expander on DAE 0 LCC A
Answer: B
Question: 13
Where can you
find the widest range of resources for VNX-related information?
A. VNX Family
Product Page
B. Support by
Product
C. Partners Web
Page
D. IP Storage
Handbook
Answer: A
Question: 14
A new VNX Unified
system has been installed. The engineer would like to verify that the hosts are
running a supported operating system and EMC PowerPath software version. What
resource should be used?
A. VNX Simple
Support Matrix
B. VNX Procedure
Generator
C. VNX
Installation Toolkit
D. VNX Product
Support Bulletins
Answer: A
Question: 15
Which resource is
required for all VNX activities performed by EMC and Partner personnel?
A. Simple VNX
Support Matrix
B. Host
Connectivity Guide
C. VNX Procedure Generator
D.
Interoperability Matrices
Answer: C
Question: 16
Where can you
obtain the VNX Procedure Generator?
A. EMC Services
Partner Web
B. VNX
Installation Toolkit
C. Unisphere
Service Manager
D. Unisphere
Answer: A
Question: 17
Where is the
collect_support_materials command located?
A. /nas/tools
B. /nas/sbin
C. /nas/bin
D.
/nas/var/emcsupport
Answer: A
Question: 18
What
comprehensive information should you gather when investigating a VNX
performance issue, where back-end configuration is a consideration?
A. SP Collects,
and NFS statistics
B.
collect_support_materials, and SP Collects
C. CIFS
statistics, and the back-end device layout
D.
collect_support_materials, and EMC Grab
Answer: B
Question: 19
An engineer is
diagnosing a VNX File system. Which file-specific data do you send them?
A.
collect_support_materials
B. SP Collects
C. SYR data
D. panic dump
Answer: A
Question: 20
An EMC service
engineer is tasked with installing a VNX Block storage system with an SPE.
After a period of 10 minutes, SP A has booted successfully and SP B's status
LED is still flashing amber. The service engineer verifies that the cabling is
correct. What is one explanation for why SP B will not boot?
A. The top LCC in
DAE 0 is faulted
B. I/O module 1
in the right SP is faulted
C. The bottom LCC
in DAE 0 is faulted
D. I/O module 1
in the left SP is faulted
Answer: A
Test Information:
Total Questions: 240
Test Number: E20-690
Vendor Name: EMC
Cert Name: EMCPE
Test Name: VNX Solutions Specialist Exam for Platform Engineers
Official Site: http://www.certsgrade.com
For
More Details: http://www.certsgrade.com/pdf/E20-690/
No comments:
Post a Comment